Skew-T Fillet Weld Gauge
Pulgadas Métrico
Check Angle of Vertical Member, Weld Acute Side, Weld Obtuse Side, Available in Inch or Metric
Skew-T Fillet Weld Gauge
Multi-Purpose Welding Gauge
(Inch) Gauge Measures: (Metric) Gauge Measures:
2.75″ x 2″ • 6.985 cm x 5.08 cm 7.62 cm x 6.35 cm • 3″ x 2.5″
Use This Gauge To Check:
• Butt Weld Height • Weld Leg • Weld Throat • Width of Weld Seam • Bevel Angle
• Under Cut • Gap Size
Multi-Purpose Welding Gauge
Offset Gauge
This gauge can be used to measure the offset between two plates over welds, fit-up bars, landing rings or any other object up to and including 1″ that might obstruct quick measuring of two plates where the Bridgecam Gauge fails.
It can also be used to measure offset of plates in gored elbows, as seen frequently in duct work, for fit-up including the angle of the parts.
Offset Gauge
0-1" / 0-25mm Electronic Depth / Pit Gauge
Large LCD – 0.0005″ (0.01mm) Resolution, ±0.001″ (0.025mm) Accuracy, 0.06″ Dia Probes, 2 3/8″ Base, Fitted Case & Battery Included, Certificate of Calibration Traceable to NIST, Measurement Scale: Inch / Metric.
0-1" / 0-25mm Electronic Depth / Pit Gauge
Digital Welding Gauge
• X-Large LCD display • Reading: Inch, Metric, Inch Fractional • 4 Angle display on body: 60°, 70°, 80°, 90° • Battery: 3V CR2032 (included) • Measuring Range: 0-1.25″ • Accuracy: 0.001″ • Resolution: 0.0005″, 0.01mm, 128th.
Digital Welding Gauge
Welding Gauge
Can Measure in Inch or Metric!
One side is Inch, the other side is Metric
The Combo-Welding Gauge can measure in Inch or Metric all of the following:
• Root Size • Fillet Weld Leg • Butt Weld Height • Fillet Weld Throat • Angle of Preparation
Welding Gauge
Adjustable Fillet Weld Gauge
Unequal Leg Measurement Feature
Measure Fillet Weld & Weld Throat Thickness, Available in Inch or Metric
Adjustable Fillet Weld Gauge
Automatic Weld Size Weld Gauge
For Accurate Calibration of Butt Fillet Type Welds, Available in Inch or Metric
Automatic Weld Size Weld Gauge
Bridge Cam Gauge
The following measurements are possible in either inches or millimeters: Angle of Preparation, Excess Weld Metal, Depth of Undercut, Depth of Pitting, Weld Throat Size, and more.
Bridge Cam Gauge
Economy Single Purpose Hi-Lo Welding Gauge
Eliminates Rejects – Improves Productivity, Available in Inch or Metric. Delivered with a protective leather-like carry pouch.
Economy Single Purpose Hi-Lo Welding Gauge
PRO Single Purpose Hi-Lo Welding Gauge
Eliminates Rejects – Improves Productivity, Available in Inch or Metric.
PRO Single Purpose Hi-Lo Welding Gauge
HI-LO Welding Gauge
Measures Internal Alignment, New Slim Design Is 30% Lighter
HI-LO Welding Gauge
"Mini Sub" Socket Weld Gauge
Check Throat Dimensions, Checks All Pipe Schedule, All Stainless Steel
"Mini Sub"
Socket Weld Gauge
Digital Pit Depth Gauge
W/Probes & Rods 1″ – 6″. Measurement Scale: Reads BOTH Inch & Metric. Probes Included: .025 & .062 Diameter. CR2032 Battery Included. Certificate of Calibration Traceable to NIST.
Digital Pit Depth Gauge
Pit Depth Gauge
Undercuts/Pits to 1/2 Inch by 1/32 Inch Increments … along with Metric Equivalent Markings. Check Undercuts/Pits, Porosity, All Stainless Steel.
Pit Depth Gauge
Pipe Pit Gauge
Range is 0 to 1/2″ in 1/64″ & .010 Increments, Arm Can be Locked in Place at Any Dimension, All Stainless Steel, Available in Inch or Metric
Pipe Pit Gauge
Pocket Bridge Cam Gauge
Check Angle of Preparation, Excess Weld Metal, Depth of Undercut, Depth of Pitting, and more.
Pocket Bridge Cam Gauge
"V-WAC" Single Weld Gauge 1/4 Inch
Undercuts/Pits to 1/4 Inch, Crowns to 1/4 Inch by 1/64 Inch Increments (Tolerance .006″). Check Undercuts/Pits, Porosity, Crowns, All Stainless Steel.
"V-WAC" Single Weld Gauge(1/4 Inch)
"V-WAC" Single Weld Gauge(0.240)
Undercuts/Pits to 0.240, Crowns to 0.240 by 0.020 Increments. Check Undercuts/Pits, Porosity, Crowns, All Stainless Steel.
"V-WAC" Single Weld Gauge(0.240)
"V-WAC" Single Weld Gauge(6mm)
Undercuts/Pits to 6mm, Crowns to 6mm by 0.5mm Increments. Check Undercuts/Pits, Porosity, Crowns, All Stainless Steel.
"V-WAC" Single Weld Gauge(6mm)
Pocket Bridge Cam Gauge
Undercuts/Pits to 0-2mm by 0.2mm Increments. Check Undercuts/Pits, All Stainless Steel.
Pit Gauge(0-2mm)
Pit Gauge(0.08")
Undercuts/Pits to 0.08″, Crowns to 0.04″ by 0.005″ Increments. Check Undercuts/Pits, Crowns, All Stainless Steel.