Dew Point Meter NOVOTEST KTR-1 is designed for rapid non-destructive measurement the temperature, humidity, dew point calculation and measurement of the surface temperature by contact method.
Dew Point Meter NOVOTEST KTR-1 allows user to measure:
– air temperature (-20 to + 125 ° C)– surface temperature (-20 to + 125 ° C)– relative humidity
– dew point temperature– difference between dew point and surface temperature
Portable Coating Thickness Gauge NOVOTEST TP-1M – device for operative non-destructive measuring of coating thickness in compliance with ISO 2808 with high measurement accuracy.Coating thickness gauge is designed to test:
Electronic thickness gauge – device which widely used in shipbuilding and automotive industries for measuring of the thickness of paint, in order to test the quality of products, also it used for determining technical condition of the tested objects.
Coating Thickness Knife Tester NOVOTEST TPN-2808 (Paint Inspection Gauge) is designed to measure the thickness of both single and multiple layer coatings on any grounds, both metallic and non-metallic. The operation principle is based on the local cut (notch) of the coating at the tested place of object with following thickness measurement of this coating. The thickness of coating is determined by the width of notch, it is possible because of the special form of cutter of the instrument. The measurement is performed by any portable measuring microscope with a suitable measuring range and discreteness.
Coating Thickness Knife Tester NOVOTEST TPN-2808 (Paint Inspection Gauge) complies with ISO 2808, ASTM B 4138, DIN EN 1071-2.
NOVOTEST ED-3D Pinhole Detector was designed for rapid non-destructive testing of the continuity of coating (e.g. porosity of film) with thickness up to 500mkm according to ASTM G62-A.Pinhole Detector is designed for testing the porosity of partially painted places and other discontinuities of protective dielectric coatings on metal products by putting low voltage through a sponge which is soaked in a liquid electrolyte with high penetrating properties.
Pulse Holiday Detector NOVOTEST SPARK-1 designed to detect pits, flaws, and holes in different non-metallic insulation coatings (such as polymers, epoxy, bitumen, etc.) and is mostly used for oil and gas metal pipelines and other objects. The device can be used while the pipeline construction, operation or service. Tested coating thickness is up to 12 mm. Such tests are needed to evaluate the oil and gas pipelines corrosion protection reliability.
The Device complies with ASTM G62-07, NACE RP0274-2004, NACE RP0490-2007, NACE SP0188-2006, ASTM D4787-08, ANSI/AWWA C214-07, ANSI/AWWA C213-07, ISO 2746:1998 & AS3894.1-2002.
How it works. The device registers high-voltage shortcuts between two electrodes, that are connected to the high-voltage source and the metal pipe (or other testing objects).
For different tasks, the device supplies with a set of different shapes and of different materials electrodes.
Mechanical depth gauge of focal corrosion.
Mechanical depth gauge is designed to comply with ASTM D 4417-B, SANS 5772, US Navy NSI 009-32, US Navy PPI 63101-000 for (depending on configuration): measures the peak-to-valley height of a blast cleaned surface; measurement the depth of focal corrosion; measures depth of narrow holes and grooves.
Digital Surface Profile Gauge NOVOTEST SP-1M is designed for profile measuring on either flat or curved surfaces. Also it can be used for measurements of surface roughness (Rz), after abrasive blasting pre-painting work.
The electronic unit is the same as Coating Thickness Gauge NOVOTEST TP-1M.
NOVOTEST SP-1M consist of electronic block of Coating Thickness Gauge NOVOTEST TP-1M and probe DSH.
Film applicator AU-823 is designed for applying layers of paint and other materials of required thickness of the layer during the complex tests according to ASTM D 823-E.
User can set the height of the gap by micrometer heads at the range of 10-6000 µm. The height of the gap should provide the necessary thickness of the layer of paint film. The applicator is to be placed on the edge of the test plate, than pour necessary amount of tested material in front of the gap and move the applicator along the plate at constant speed of 5-10 cm/s, dispensing continuous layer of the tested material on the plate.
The High Precision Grindometer NOVOTEST M-1524 has a single groove.
Grind gauges are used to determine particle size and fineness of grind. The tested materials are paints, chocolates, inks, coating materials and so on.
The device is made of hardened stainless steel. The scale on the top of the device is graduated in micrometers.
STANDARDS:ASTM D 1210, AS/NZS 1580.204.1, DIN 53203, EN 21524, FTMS 141 4411.1, ISO 1524, JIS K 5600-2-5, NF T30-046